Mahwah NJ Furnace and Air Conditioning Repair Installation Service

Air Conditioning System Repair Service: While inspecting a homeowner’s HVAC system, I found that damaged insulation on refrigerant lines was leading to energy loss and inefficiencies. I replaced the compromised insulation to enhance temperature control and improve system efficiency.

AC System Repairs: During a detailed assessment of a client’s HVAC unit, I detected a refrigerant line restriction caused by a kink in the piping. I straightened the kink, restoring proper refrigerant flow and optimizing system performance.

Arrived onsite for maintenance on 6 geothermal cooling systems. Changed filters that were available from customer. Review filters that need to be purchased. Clear out condensate lines. Confirmed operation of all systems Performed inspection of the mechanical, performance and safety systems. Note that none of the UV lights are operation. The bulbs need to be changed. Recommend replacing with a different UV light brand that has more cost effective bulbs.

Arrived on site for duct cleaning of supply and return lines covered blower motor and filter shut off system and began scrubbing return lines first Removed screws from registers on ceiling to scrub microbial growth off of the front and back plate of registers. Ran drop cloth and corner covers to prevent property damage throughout the house Scrubbed the supply and return lines also scrubbed trunk of duct work at each end Spermicide the entire system re patched holes in duct work tested unit for proper functionality All components are working as they should at this time Side note: filter sizes (below) 24 x 30 x 1 20 x 12 x 1

We arrived on site to install a new crown velocity wall hung boiler. We drained down and removed the old NTI boiler. We removed and labeled all piping and wiring and we installed a made a wall to hang the boiler piping and necessary parts. We proceeded to pipe level and adapt the boiler installing honeywell's own valves new magna clean for the system and new taco 10 and grumpus circulator pumps. We piped in the radiant lines and the heating loops. We installed new ball valves on each line for proper purging. We filled checked for leaks and purged out the whole system. We rewired The high and low voltage for the system installing a new neutralizer pump and receptacle. We programmed the system tested all functions everything is operational at this time.

We arrived on site to install a new crown velocity wall hung boiler. We drained down and removed the old NTI boiler. We removed and labeled all piping and wiring and we installed a made a wall to hang the boiler piping and necessary parts. We proceeded to pipe level and adapt the boiler installing honeywell's own valves new magna clean for the system and new taco 10 and grumpus circulator pumps. We piped in the radiant lines and the heating loops. We installed new ball valves on each line for proper purging. We filled checked for leaks and purged out the whole system. We rewired The high and low voltage for the system installing a new neutralizer pump and receptacle. We programmed the system tested all functions everything is operational at this time.

Arrived on-site to replace the filter and ensure optimal system performance.

Service Call Note: Issue: Arrived on-site for boiler maintenance. Action Taken: • Replaced the inner body of the Honeywell zone valve. • Applied Teflon tape and pipe dope to threaded connections to ensure a proper seal. • Installed a cap on the drain leg below the backflow valve. • Purged the boiler and tested all zones to confirm proper system flow. Outcome: No air detected in the system. All zones are operating as expected. No further maintenance required at this time.

AC System Repair: Investigating cooling inefficiencies, I identified and repaired a refrigerant leak in the condenser coil. Restoring optimal refrigerant levels improved performance and efficiency, ensuring the homeowner’s comfort without further concerns.

Winter HVAC Tune-Up: Conducted a detailed maintenance service on a homeowner’s HVAC system. Cleaned the heat exchanger, inspected and tightened electrical connections, and replaced the air filter. This proactive service helps maintain peak performance and energy efficiency.

Arrived onsite for leak from high efficiency gas fired boiler. Performed diagnostic and confirmed nothing is leaking from inside the boiler. Observed dirty combustion drain trap but it wasn’t leaking. Observed a fault in the water removal system. Also noticed the system does not a neutralizer pellets which is needed for the acidic condensation from a high efficiency boiler. Recommend maintenance on the boiler. Homeowner will wait until next season around October.

Arrived onsite for heating maintenance on 1 gas fired furnace located in second floor hallway closet Furnace System: Turn heat on and confirmed operation. Changed 14x25x1 filter provided by customer. Brushed and Wiped down furnance blower cabinet and gas burners. Burners fired and are in good working order. No visual impingement detected. Checked electrical. Cleaned the flame sensor. Measure temperature rise at 45 degrees. Performed Combustion Test. System is operating as it should.

Installed new warranty evaporator coil in Coleman air handler in attic. We remove the old coil We braised in copper linset ran drain lines. We pressure tested the system to 300 PSI found no leaks we evacuated the system to 500 microns and charged with 6 lb and 12 oz of R410A refrigerant. Everything is operational at this time need to return springtime just to check pressures.

Arrived onsite for heating maintenance on gas fired furnace located in the basement. Basement Furnace System: Turn heat on and confirmed operation. Changed polarized filter provided by customer. Observed the UV light requires replacement. Brushed and Wiped down furnace blower cabinet and gas burners. Burners fired and are in good working order. No visual impingement detected. Checked electrical.. Cleaned the flame sensor. Measure temperature rise at 41 degrees. System is operating as it should. Will have the office order more polarized filter media and replacement UV bulbs

Performed leak test on Coleman system. Recoverd 410-A from system left 3lb in system. Pumped up with nitrogen 350psi performed test on coil found coil leaking. Need to check on warranty. Office needs to call for the warranty coil and set up an appointment with the customer to replace his coil. I left nitrogen in the system so whoever goes back will know. Model number is in the system and I also gave it to Allison

Arrived onsite for heating maintenance gas fired furnace 1 in basement with humidifier. Basement Furnace System: Turn heat on and confirmed operation.. Brushed and Wiped down furnace blower cabinet and gas burners. Burners fired and are in good working order. No visual impingement detected. Checked electrical. Cleaned the flame sensor. Measure temperature rise at 27 degrees. Inspected humidifier and confirmed operation. Water panel in good shape. System is operating as it should.

AC Repair: A homeowner faced an overheating AC system during peak summer. We diagnosed a malfunctioning condenser fan motor and replaced it with a high-quality component.

Arrived onsite to replace leaking temperature pressure relief valve on water heater. The part supplied by the homeowner did not fit. Homeowner agreed to having Climate Plus provide and install the proper temperature pressure relief valve. Installed valve. Attached drip leg. Refilled the water heater. Light the pilot light and confirmed operation of the water heater. Set water heater to level B. Used wet dry vac to clear the water basin. System working as it should.

Arrived onsite for issue with the heating same. Follow up from recent repair. Found the high temperature safety control system turning the the system off around 170-180 degrees and turning on the system at 100-110 degrees this is improvement from previous part which wouldn’t turn the system back on 80-90 degrees. Increased the high heat limit setting to 180-190. Observed the boiler start up again at 120-13 degrees. Ideally the boiler low limit should be at 150-160 degrees.There is a possible blockage inside the boiler’s heat exchanger which is causing an inaccurate sensor reading. Most likely the boiler will need to be replaced. We will try to replace the part to confirmed there isn’t a fault in the new part’s sensor.

Arrived onsite for heating maintenance 1 gas fired furnace. Turn heat on and confirmed operation. Brushed and Wiped down furnace blower cabinet and gas burners. Burners fired and are in good working order. No visual impingement detected. Checked electrical. Measured 56 degree heat rise. Cleaned the flame rectification system. System is operating as it should. Performed flush and inspection of the water heater. The water was clear of sediment. Did not observe any rust or sign of imminent water failure.

Arrived onsite for issue with the heating same. Follow up from recent repair. Found the high temperature safety control system turning the the system off around 170-180 degrees and turning on the system at 100-110 degrees this is improvement from previous part which wouldn’t turn the system back on 80-90 degrees. Increased the high heat limit setting to 180-190. Observed the boiler start up again at 120-13 degrees. Ideally the boiler low limit should be at 150-160 degrees. There is a possible blockage inside the boiler’s heat exchanger which is causing an inaccurate sensor reading. Most likely the boiler will need to be replaced. We will try to replace the part to confirmed there isn’t a fault in the new part’s sensor.

Arrived onsite for no heating call. Confirmed call for heat from thermostat. Confirmed power to the system. Found no signal from furnace to thermostat. Found a fault in the condensate pump safety switch. Landlord agreed to replace the water removal system to correct the issue. Confirmed operation of the heat after completing the repair.

Heat Pump Tune-Up: A client noticed reduced performance in their heat pump during the winter months. Our technicians addressed the issue with a detailed tune-up, adjusting thermostat settings and clearing debris from the outdoor unit. The heat pump now functions more efficiently, providing the reliable warmth the client expected.

Arrived onsite for no heating call. Confirmed call for heat from thermostat. Confirmed power to the system. Found no signal from furnace to thermostat. Found a fault in the condensate pump safety switch. Landlord agreed to replace the water removal system to correct the issue. Confirmed operation of the heat after completing the repair.

Arrived onsite for maintenance for one gas fired high efficiency boiler. Requested the customer turn on the thermostats up to heat and confirm operation of the boiler and each zone valve. Turned the boiler off and removed heat exchanger cover. Cleaned heat exchanger. Performed a visual inspection of all electrical and inspected all external water components such as the exp tank, fill valve, backflow preventer and the circulator pump. Clear condensate lines. Found fault in the fuel delivery system. There is a noise coming from the motor. Shared the findings with the homeowner. Since the system is currently working, we will wait for failure before fixing. Also found fault in the ignition system. The ignitor ant sensor are worn. Recommend replacing. Will provide estimate. system is operating and heating at this time. Note system is approaching age where replacement may make sense.